Global Sources
EE Times-Asia
Stay in touch with EE Times Asia

( File format: PDF, 266 KB )
6-Channel Serial And Parallel Low-Side Pre-FET Driver (Rev. B)
Texas Instruments

The TPIC46L01, TPIC46L02, and TPIC46L03 are low-side predrivers that provide serial input interface and parallel input interface to control six external field-effect transistor(FET) power switches such as offered in the Texas Instruments TPIC family of power arrays. These devices are designed primarily for low-frequency switching, inductive load applications such as solenoids and relays. Fault status for each channel is available in a serial-data format. Each driver channel has independent off-state open-load detection and on-state shorted-load/short-to-battery detection. Battery overvoltage and undervoltage detection and shutdown are provided. Battery and output load faults provide real-time fault reporting to the controller. Each channel also provides inductive-voltage-transient protection for the external FET. These devices provide control of output channels through a serial input interface or a parallel input interface. A command to enable the output from either interface enables the respective channel GATE output to the external FET. The serial input interface is recommended when the number of signals between the control device and the predriver must be minimized, and the speed of operation is not critical. In applications where the predriver must respond very quickly or asynchronously, the parallel input interface is recommended. For serial operation, the control device must transition CS\ from high to low to activate the serial input interface. When this occurs, SDO is enabled, fault data is latched into the serial input interface, and the FLT\ flag is refreshed. Data is clocked into the serial registers on low-to-high transitions of SCLK through SDI. Each string of data must consist of 8 bits of data. In applications where multiple devices are cascaded together, the string of data must consist of 8 bits for each device. A high data bit turns the respective output channel on and a low data bit turns it off. Fault data for the device is clocked out of SDO as serial input data is clocked into the device. Fault data consists of fault flags for the over-battery voltage (bit 8), under-battery voltage (bit 7) (not on TPIC46L03), and shorted/open-load flags (bits 1-6) for each of the six output channels. A logic-high bit in the fault data indicates a fault and a logic-low bit indicates that no fault is present on that channel. Fault register bits are set or cleared asynchronously to reflect the current state of the hardware. The fault must be present when CS\ is transitioned from high to low to be captured and reported in the serial fault data. New faults cannot be captured in the serial register when CS\ is low. CS\ must be transitioned high after all of the serial data has been clocked into the device. A low-to-high transition of CS\ transfers the last 6 bits of serial data to the output buffer, puts SDO in a high-impedance state, and clears and reenables the fault register. The TPIC46L01/L02/L03 was designed to allow the serial input ......
6-Channel Serial-In/Parallel-In Low-side Pre-FET Driver Device Can Be Cascaded Internal 55-V Inductive Load Clamp and VGS Protection Clamp for External Power FETs Independent Shorted-Load/Short-to-Battery Fault Detection on All Drain Terminals Independent Off-State Open-Load Fault Sense Over-Battery-Voltage Lockout Protection and Fault Reporting Under-Battery Voltage Lockout Protection for TPIC46L01 and TPIC46L02 Asynchronous Open-Drain Fault Flag Device Output Can Be Wire-ORed With Multiple External Devices Fault Status Returned Through Serial Output Terminal Internal Global Power-On Reset of Device High-Impedance CMOS Compatible Inputs With Hysteresis TPIC46L01 and TPIC46L03 Disables the Gate Output When a Shorted-Load Fault Occurs TPIC46L02 Transitions the Gate Output to a Low-Duty Cycle PWM Mode When a Shorted-Load Fault Occurs

Related Datasheets
Part Number Description Category
? ?TPIC2101 DC Brush Motor Controller ICs, RF/Wireless
? ?TPIC2603 6-Channel Serial Interface Low-Side Driver (Rev. A) ICs, RF/Wireless
? ?TPIC44H01 4-Channel Serial And Parallel High-Side Pre-Driver ICs, RF/Wireless
? ?TPIC44L02 4-Channel Serial And Parallel Low-Side Pre-FET Driver (Rev. B) ICs, RF/Wireless
? ?TPIC46L01 6-Channel Serial And Parallel Low-Side Pre-FET Driver (Rev. B) ICs, RF/Wireless
? ?TPIC46L02 6-Channel Serial And Parallel Low-Side Pre-FET Driver (Rev. B) ICs, RF/Wireless
? ?TPS5430 3-A Wide Input Range Step-Down Swift(TM) Converter (Rev. C) ICs, Interface
? ?TPS78601 Ultralow-Noise, High-PSRR, Fast, RF, 1.5-A Low-Dropout Linear Regulators (Rev. G) ICs, Interface
? ?TXB0108 TXB0108 (Rev. A) EDA - IC Design

As the hyperlinked contents/websites are those of third parties, we cannot vouch for their accuracy or legitimacy.
Interviews & Viewpoints


Learn how senior executives are seeing the industry from interviews and contributed opinions.

Bloggers Say

Bloggers Say

See what engineers like you are posting on our pages.

Back to Top