Global Sources
EE Times-Asia
Stay in touch with EE Times Asia
EE Times-Asia > Advanced Search > external op-amp mode

external op-amp mode Search results

?
?
total search38 articles
2003-10-03 Operation of A-D Converter (in single sweep mode
This application note presents the operation of A-D Converter in single sweep mode
2003-10-03 Operation of A-D Converter (in repeat mode
This application note presents the operation of A-D Converter in repeat mode
2003-10-03 Operation of A-D Converter (in one-shot mode, external op-amp connection mode)
This application note presents the operation of A-D Converter in one-shot mode and in external op-amp connection mode.
2009-08-14 Op amp guarantees operation down to 1.6V
National Semiconductor's PowerWise LPV521 extends battery life in portable equipment, low power apps.
2010-05-19 Op amp combines high speed, low DC errors
From National Semiconductor comes a high-speed op amp claimed to deliver the lowest noise (0.69nV/sqrt Hz) with -3dB bandwidth of 900MHz at a gain of 10
2003-06-09 Linear Tech op amp features a fixed gain of two
The LTC1992-2 differential input, output amplifier from Linear Technology Corp. features a fixed gain of two.
2009-03-31 10MHz op amp features rail-to-rail I/O
austriamicrosystems has launched the AS1713 operational amplifier, a high output differential line receiver with a 10MHz, 10V/?s, rail-to-rail I/O performance.
2005-05-02 Op amp tailored for TFT LCDs
A high-performance step-up regulator with two high-current operational amplifiers for active-matrix, thin-film transistor (TFT) LCDs in notebook and automotive applications was unveiled by Maxim Integrated Products
2004-10-13 National op amp offers power select pin
The LMV422 from National features a unique power-saving mode that allows customers to reduce power consumption while maintaining an active circuit
2007-09-25 Dual op amp extends battery life in portable apps
ADI's AD8506 is a low-power CMOS dual op amp with rail-to-rail inputs and output and is designed for battery-powered portable applications
2015-02-03 Simplify compensation with LED buck regulator
Find out how to compensate the control loop in a peak current-mode controller to ensure stability when you are regulating current rather than the output voltage
2013-02-13 Perform audio line receiver impedance balancing
When the design specification for a line receiver requires high performance, an impedance-balanced input or predictable gain, the cross-coupled double-balanced configuration is a worthy contender.
2014-04-04 Optimisation of photodiode sensor circuit design
Know the important steps in obtaining the best possible system performance.
2005-08-01 Cutting RF power in W-CDMA phones
Power dissipation problems in W-CDMA phones can be solved by adjusting power amplifier efficiency and voltage requirements
2007-05-04 Op amps suit automotive, industrial applications
STMicroelectronics' TS507 high-precision op amp features an ultralow input offset voltage guaranteed over a wide common-mode voltage range, making it suitable for automotive and industrial applications
2007-05-09 High-precision op-amps suit automotive, industrial apps
ST has released TS507, a high-precision op-amp that benefits customers with an ultra-low input offset voltage guaranteed over a wide common-mode voltage range
2008-12-17 FAQs: Amplifiers (Part 3)
Part 3 answers questions likes what is a closed loop buffer? What is a open loop gain, voltage feedback op amp? What is an amplifier's intercept point
2013-12-04 ADC in SoC: Mere placeholder or vital subsection?
Evaluating an integrated ADC in an SoC can be a little bit trickier than evaluating an external ADC
2014-07-28 Utilising ARM Cortex-M based SoCs (Part 2)
The second instalment compares the capabilities of a standard microcontroller approach to the design of an embedded application to that of a system on chip approach.
2014-04-16 Utilise audio amps for voltage splitting (Part 3)
Here's a look at voltage splitters based on power audio amplifiers.
2003-02-26 STMicro expands 8-bit Flash MCU line
The company has expanded its ST7Lite series of 8-bit Flash MCUs with the introduction of the ST7FLite1 and ST7FLite2 units.
2005-09-16 ST expands ST7Lite MCU family
STMicroelectronics announced a new series of 8bit flash microcontrollers (MCUs) within its low-cost ST7Lite family, adding new embedded peripherals to the ST7Lite feature set.
2011-11-01 Signal chain basics: Analyzing RL drive in ECG front end with SPICE
Learn about the analog front end for this ubiquitous, vital medical instrument.
2005-08-05 Sensor IC packs 8051 core
As a 'smart sensor' conditioner, the SSP1492 from Sensor Platforms gives any sensor the ability for self-identification.
2008-08-01 Scrutinizing power-supply stability in a multiloop system
Analyzing a power system's stability begins with a look at the open-loop Bode plot of a buck or flyback converter's power stage. From this plot, the designer extracts phase and gain data for the frequency range of interest.
2013-01-29 Save power in LCD TVs with LED driving techniques
New design techniques in LED driver circuits promise to deliver significant energy savings that will go a long way to helping TV manufacturers meet the tough requirements for power consumption.
2010-03-12 Pulse-CO oximeter takes blood analysis out of lab
Few disciplines can turn the cold science of metrology into pure art as quickly as medical diagnostics. Here's a teardown of the Masimo's Radical-7 Signal Extraction Pulse-CO Oximeter.
2006-04-10 Op amps are built on VIP50 BiCMOS process
National Semiconductor announced nine single, dual and quad operational amplifiers built on its proprietary VIP50 BiCMOS process technology.
2008-05-15 MCUs tailored for compact, battery-powered systems
NEC Electronics' new line of 16bit All Flash MCUs are optimized for compact, low-power systems that are driven by battery.
2008-06-24 Low power design for analog/mixed-signal IP
Power reduction and management techniques using multiple clock and power domains, dynamic voltage and frequency scaling and power gating are effective for digital circuits but for analog design, lowering power consumption must be considered early in the design phase.
Bloggers Say

Bloggers Say

See what engineers like you are posting on our pages.

?
?
Back to Top