Global Sources
EE Times-Asia
Stay in touch with EE Times Asia
EE Times-Asia > Advanced Search > surface mount connector

surface mount connector Search results

?
?
total search140 articles
2005-08-04 HDMI receptacle fits consumer electronics
Supporting the next-generation interface for consumer electronic products such as digital televisions, DVD players and STBs, FCI has developed a new HDMI receptacle that is RoHS compliant and uses gold plating in the contact area.
2009-01-15 HDMI receiver with CEC improves HDTV quality
Analog Devices has released of what it claims to be the first deep color HDMI receiver integrated with a Consumer Electronics Control (CEC) controller and analog interface.
2008-02-14 Guitar Hero jams go wireless
Much as musicians often go wireless to allow for freedom onstage, the Xbox 360 Guitar Hero III Les Paul wireless controller, manufactured by RedOctane, lets players do spinning jumps off the couch.
2007-04-17 Firmware adds WAAS, EGNOC to GPS receiver
Trimble Navigation has introduced new firmware that adds Wide Area Augmentation System (WAAS) and European Geostationary Navigation Overlay Service (EGNOS) capability to its ultrathin Copernicus GPS receiver.
2013-07-25 FCI rolls 12Gbps SAS receptacles for enterprise storage apps
The 12Gbps SAS connectors from FCI complies with the SAS 3.0 and SFF8680 specification and are designed to support hot plugging and blind mating of HDDs and SSDs.
2015-01-19 Enhanced SMT pad design for signal transmission
In this article, we present an analysis that proves that insertion of a cut-out on the reference plane underneath the SMT pads reduces the impedance mismatch and increases the bandwidth of the transmission line.
2014-09-02 Enable low-cost isoSPI coupling for battery systems
By using an AC-coupling method, we can eliminate the double insulation requirement, and therefore mitigate the cost impact of high voltage isoSPI systems.
2015-07-15 E-band cost, reliability concerns in MMIC packaging
Traditional semiconductor packaging approaches either cost too much or suffer from signal integrity issues. However, new techniques are becoming available that can address these problems.
2007-05-08 Dual/quad-port gigabit transformer modules suit industrial Ethernet apps
Pulse's new dual- and quad-port gigabit discrete isolation transformer modules feature an extended temperature range, making them suitable for industrial Ethernet applications.
2007-01-09 Draft-n router claims 300Mbps wireless speed
The Netgear WNR854T access point provides backward compatibility with 802.11b/g, but draft-n capability lets it deliver wireless connections at up to a raw claimed 300Mbps.
2008-08-01 Developing a green product development strategy
One of the most difficult steps in the initiation of a green product development strategy is where to get started. The green knowledge base for product development is widely distributed and not readily available within the organization, in the design or process teams.
2013-11-04 Design the appropriate high-speed ATE hardware
Designing ATE hardware should not be taken lightly as a simple error could cost you another four to six weeks on your schedule.
2008-02-07 Cordless phone enters next phase
The VTech 6032 is a handset/base combo built around the newly minted DECT 6.0 cordless standard.
2010-10-29 CFast flash memory headers enable design flexibility
3M launches new series of CFast card flash memory headers
2008-08-11 Bluetooth kit makes embedded design simple
ZBA Inc. has introduced the BT44-DEV-KIT Bluetooth evaluation kit, which includes Bluetooth dongle access to the company's BT44 evaluation board.
2007-11-13 Backplane, power module connectors meet MicroTCA specs
FCI has developed backplane signal connectors and power module input connectors that are fully compliant with the MicroTCA specification issued by PICMG.
2015-11-20 Test active optical cables during design, production
Testing and analysis done at critical junctures during the design process can further reduce costs by optimising the design for high yield given specified manufacturing tolerances.
2006-04-19 Bivar solution helps engineers to easily incorporate latest LED tech
Bivar introduced a 1W LED Block series designed for use in industrial, automotive, architectural, backlighting and intense single or multiple lighting apps.
2004-06-29 Agilent connectorless logic analyzer adopted as standard
Agilent announced that its Pro Series soft touch connectorless logic analyzer probe interface has been adopted by logic analyzer vendors as the industry standard.
2013-08-13 13.5mm solderless LED flashes 1500lm of brightness.
The Soleriq S 13 from Osram Opto can be installed in LED luminaires as a so-called retrofit, replacing halogen spotlights with high wattage.
Bloggers Say

Bloggers Say

See what engineers like you are posting on our pages.

?
?
Back to Top